Page 5: Factory Settings Page 7 Limit Teaching P. Timer period can be selected from 0. Page 10 Page 11 Teaches only the status condition in which no sensing object is within sensing range status in Limit Teaching which incident light intensity is stable. This method is used to set a threshold value for conducting sensing in the presence of a background, or when extremely small objects are to be detected.
Page 12 Full-auto teaching is used to set the threshould value while the workpieces are still moving on the Full-Auto Teaching production line, without stopping the production line.
Page 13 Page 17 Page 19 Press the 6If the [Jog switch] is pressed, the threshold Jog switch. Page Output Operation Setting Mode Timer period Delay increments 0. Refer to p. Page Timer Setting Function Fx Page Hysteresis Function Page Stability Function Page 31 Press the 9 If the [Jog switch] is pressed, the digital display will quickly Jog switch. The digital display will quickly blink 3 times to confirm the setting. Page Digital Display Setting Function Digital Display Setting Function This function allows the display to be switched among the different digital displays incident light intensity display, percentage display, peak hold display, bottom hold display However, when FX is in window comparator mode, the percentage display function cannot be utilized.
Page Digital Display Inversion Function Digital Display Inversion Function This function can be used to invert the display orientation, according to the direction of amplifier installation. If no operations are performed for 20 sec. Page Pro3 Mode PRO3 mode can load configuration settings from the data bank and can save configuration settings to the data bank. Three different sets of configuration settings can be stored within the data banks, in channels 1 to 3 These configuration settings will not be deleted, unless they are intentionally overwritten by the data bank save setting function.
Data Bank Load Setting Function This function allows configuration settings information from the data bank to be selected and then loaded. This feature allows settings to be changed quickly at times of reconfiguration, etc. Page Pro4 Mode However, the interference prevention function is only effective for up to 4 consecutive FX units, and for up to 8 consecutive FX units. In addition, if FX and FX units are connected together, then interference prevention will only be effective for up to 4 units.
Therefore, if units of both models must be utilized when connected together, then similar models should be connected side by side. By utilizing optical communications, the existing settings within the data banks of connected amplifiers can be loaded in a single step. This function allows the configuration settings information in an amplifier to be saved to other connected amplifiers, in a single step.
Page 47 Page Pro5 Mode It also permits the unit to be reset re-initialized. Direct Code FX , FX and FX contain certain encoded basic configuration information that can be set by inputting a 4-digit code.
Page 49 If the Timer period is set to a time that does not correspond to a direct code value, then the remaining codes, other than that in the fourth digit, will still remain valid.
Page Code Setting Function Code Setting Function The input of a 4-digit code allows the configuration to be set directly, without the need to set each individual function. Page 0-Adjust Setting Function Page Adjust Lock Setting Function Page Setting Reset Function Setting Reset Function This function will cause all configuration settings to revert to factory settings. However, any settings that have been saved within the data bank will not be changed.
The output mode can be selected from either normal mode or window comparator : Window Comparator Mode mode. Window Comparator Mode Setting Function Either normal mode or window comparator mode can be selected. Page Window Comparator Hysteresis Function This manual is also suitable for: Fx Fx Print page 1 Print document 57 pages.
Rename the bookmark. Delete bookmark? Refer to p. If no operations are performed for 20 sec. Sunx FX 30 7 If the [Jog switch] is turned, the digital display will blink. Select the desired timer operation. B If the [Jog switch] is pressed, the digital display will quickly blink 3 times, confirming the setting.
Refer t … 3. Sunx FX Press the MODE key 4 … Interference prevention function 1 Interference prevention function 2 Press the Jog switch. However, any settings that have been saved within the data bank will not be changed.
Please refer … Settings for four functions can be configured. Incident light intensity is displayed in real time. Inside the device there are no parts that are user The contents are subject to change without notice. The ZM provides watts of clean power. Six input channels with individual l It sounds like the best handheld micro-phones—full, clear, and distortion-free, even with the loudest singers. Its noise-canceling ability reje PowerBass ATM ATM
0コメント